In search of a better result.

B9 Core Series - Ideas and Discussions
Provin
B9 Maker
B9 Maker
Posts: 16

In search of a better result.

Post#1 » Wed Oct 25, 2017 10:14 am

I have some problem with quality printing ....
I would like to know if you can achieve better results with CORE 550 in terms of impressions.
Attachments
WhatsApp Image 2017-10-25 at 14.10.48 (3).jpeg
WhatsApp Image 2017-10-25 at 14.10.48 (4).jpeg
WhatsApp Image 2017-10-25 at 14.10.49.jpeg
WhatsApp Image 2017-10-25 at 14.10.49 (1).jpeg
WhatsApp Image 2017-10-25 at 14.10.49 (2).jpeg
WhatsApp Image 2017-10-25 at 14.10.49 (3).jpeg
WhatsApp Image 2017-10-25 at 14.10.50.jpeg
WhatsApp Image 2017-10-25 at 14.10.50 (1).jpeg
WhatsApp Image 2017-10-25 at 14.10.50 (2).jpeg

alitans
B9 Maker
B9 Maker
Posts: 30

Re: In search of a better result.

Post#2 » Wed Oct 25, 2017 4:28 pm

Update your printer's firmware if you haven't yet.

Recharge your duraVat at least for half an hour.

Provin
B9 Maker
B9 Maker
Posts: 16

Re: In search of a better result.

Post#3 » Thu Oct 26, 2017 12:30 pm

Problems with print quality.

Hello friends.

Good afternoon, how are you?

Could you send me a picture of how your prints are so I can analyze how much I'm behind in print quality.
Attachments
WhatsApp Image 2017-10-26 at 15.16.54.jpeg
WhatsApp Image 2017-10-26 at 15.17.04.jpeg
WhatsApp Image 2017-10-26 at 16.10.03.jpeg
WhatsApp Image 2017-10-26 at 16.10.30.jpeg
WhatsApp Image 2017-10-26 at 16.08.15.jpeg
WhatsApp Image 2017-10-26 at 16.08.15 (1).jpeg
WhatsApp Image 2017-10-26 at 16.08.15 (2).jpeg
WhatsApp Image 2017-10-26 at 16.08.16.jpeg
WhatsApp Image 2017-10-26 at 16.08.16 (1).jpeg

User avatar
akgold
B9 Wizard
B9 Wizard
Posts: 2071

Re: In search of a better result.

Post#4 » Thu Oct 26, 2017 12:46 pm

alitans wrote:Update your printer's firmware if you haven't yet.

Recharge your duraVat at least for half an hour.


And tell us what you are printing at 20 30 50 ???
show us the lay outs
I'm so far behind I think I'm First !!

Provin
B9 Maker
B9 Maker
Posts: 16

Re: In search of a better result.

Post#5 » Thu Oct 26, 2017 1:02 pm

30um...
firmware 48.
Attachments
b9.JPG

Provin
B9 Maker
B9 Maker
Posts: 16

Re: In search of a better result.

Post#6 » Thu Oct 26, 2017 1:24 pm

Slice
Attachments
b9.JPG
b9 - slice.JPG

User avatar
akgold
B9 Wizard
B9 Wizard
Posts: 2071

Re: In search of a better result.

Post#7 » Thu Oct 26, 2017 5:20 pm

I wouldn't print it this way.
I would eliminate the bail on the cross and print snap it to floor print it flat on the table get rid of all those casting sprues on all of the items you show
All three of those stone settings can also snap to the floor as long as they were all set flat to planer before you made the STLs
if not then delete the sprues and print them at an angle about 10 up from the back on all of them.

Don't print your sprues to the items it is much better to use wax sprues to the items as the wax melts out and is eliminated allowing the ash form resin to evac much better.
I'm so far behind I think I'm First !!

Provin
B9 Maker
B9 Maker
Posts: 16

Re: In search of a better result.

Post#8 » Tue Oct 31, 2017 4:04 am

Good Morning,

I can not really eliminate the Sprues, because I'm doing it in the 180 ° silicone with BLACK.

Return to “General Discussion”

Who is online

Users browsing this forum: No registered users and 1 guest

Close Menu Shop Forum