Vat table problem .. any one had this?

Software issues and solutions
User avatar
mikej
B9 Moderator
B9 Moderator
Posts: 4189
Contact:

Re: Vat table problem .. any one had this?

Post#21 » Mon Apr 27, 2015 8:57 am

mazen2014 wrote:ok done ,, 2 are shown .. so i need to select the the 1920x1080 of the two ?


Correct. Based on your selected configuration ("B9Creator v1.2.0, XY at 30 microns"), I am assuming you have the v1.2 hardware which includes the Vivitek D912HD projector (not the older D535).
Measure Twice, Cut Once.

User avatar
mazen2014
B9 Maker
B9 Maker
Posts: 157

Re: Vat table problem .. any one had this?

Post#22 » Mon Apr 27, 2015 10:55 am

it went fine .. tommorrow first printing test...
ONE SHIP ONE CAPTAIN

User avatar
mikej
B9 Moderator
B9 Moderator
Posts: 4189
Contact:

Re: Vat table problem .. any one had this?

Post#23 » Mon Apr 27, 2015 11:28 am

good luck!
Measure Twice, Cut Once.

User avatar
mazen2014
B9 Maker
B9 Maker
Posts: 157

Re: Vat table problem .. any one had this?

Post#24 » Sat May 02, 2015 5:30 am

Hello Mikej ,, I am installing this file you told me about for the third time ,, every thing is going fine with the machine but suddenly the print button on the b9 table changes to preview , then I go to check out what is wrong , I find the printer calibration is turned off ,, then i go to the printer management to check , I find that the configuration management is empty , then I re install the one in the photo again ..
Attachments
downloading.jpg
downloading.jpg (34.71 KiB) Viewed 4718 times
ONE SHIP ONE CAPTAIN

User avatar
mazen2014
B9 Maker
B9 Maker
Posts: 157

Re: Vat table problem .. any one had this?

Post#25 » Sat May 02, 2015 5:37 am

Mikej ..in photo .. the purple cable comes from the computer , is it in the right place??
Attachments
cables.jpg
cables.jpg (18.81 KiB) Viewed 4717 times
ONE SHIP ONE CAPTAIN

User avatar
mikej
B9 Moderator
B9 Moderator
Posts: 4189
Contact:

Re: Vat table problem .. any one had this?

Post#26 » Sat May 02, 2015 7:44 am

Assuming the purple cable is connected to your computer's secondary vga output port, that should be fine.
Measure Twice, Cut Once.

User avatar
mazen2014
B9 Maker
B9 Maker
Posts: 157

Re: Vat table problem .. any one had this?

Post#27 » Sat May 09, 2015 8:09 am

Mike j .. i installed the 1.8 software .. and did the first test .. but in the mid time of printing .. an error table occured .. saying mechanism jamed .. and i looked at the projector and found it projecting the windows main screen .. how can I fix it ?
Attachments
20150509_170504.jpg
ONE SHIP ONE CAPTAIN

User avatar
Robert Howle
B9 Creator
B9 Creator
Posts: 6620

Re: Vat table problem .. any one had this?

Post#28 » Sat May 09, 2015 9:19 am

Go to display settings and "Extend" display. Do not use "duplicate". Some of the windows os has "add projecter". Make sure to choose the correct resolution for the "Exteded" display. Second image is the settings on my lap top (Display 1)

Robert Howle
Extend display 2.JPG
Extend Display 1.JPG
Dance like nobody's watching!

User avatar
mazen2014
B9 Maker
B9 Maker
Posts: 157

Re: Vat table problem .. any one had this?

Post#29 » Sat May 09, 2015 9:44 am

Thanx Robert .. i did what you said befor i printed .. and the time of the print was 45 minits . And it stoped and did the problem at the 30 minits ..
i followed instructions of mikej video about this multy display but . One thing i couldnt fine is the task bar button that doesnt allow to show task bar on multiple displays .. i think i have a differnt windows than mikes in the video .. i ll try to double check all of this one more time ..
ONE SHIP ONE CAPTAIN

User avatar
mazen2014
B9 Maker
B9 Maker
Posts: 157

Re: Vat table problem .. any one had this?

Post#30 » Mon May 11, 2015 7:03 am

I double check one more time same thaing hsppened in the middle time of printing the error box came up and the projector projected the main screen .. any solutions ??
ONE SHIP ONE CAPTAIN

User avatar
mikej
B9 Moderator
B9 Moderator
Posts: 4189
Contact:

Re: Vat table problem .. any one had this?

Post#31 » Mon May 11, 2015 7:10 am

What error box (what message?)

Can you upload the latest log file (located in documents/B9Creator/B9Logs/B9Creator_LOG_xxxxxx.txt)
Measure Twice, Cut Once.

User avatar
Robert Howle
B9 Creator
B9 Creator
Posts: 6620

Re: Vat table problem .. any one had this?

Post#32 » Mon May 11, 2015 12:21 pm

Have u set all the power saver settings to "never" so that there is no change to the screen or computer (screen saver off, dim screen off, sleep mode off, etc). Also there can be no updates installed while printing that cause a puter restart.
Dance like nobody's watching!

User avatar
mazen2014
B9 Maker
B9 Maker
Posts: 157

Re: Vat table problem .. any one had this?

Post#33 » Mon May 11, 2015 1:16 pm

photos
Attachments
20150511_221217.jpg
20150511_221317.jpg
ONE SHIP ONE CAPTAIN

User avatar
mazen2014
B9 Maker
B9 Maker
Posts: 157

Re: Vat table problem .. any one had this?

Post#34 » Mon May 11, 2015 1:17 pm

2
Attachments
20150511_221146.jpg
ONE SHIP ONE CAPTAIN

User avatar
mazen2014
B9 Maker
B9 Maker
Posts: 157

Re: Vat table problem .. any one had this?

Post#35 » Mon May 11, 2015 1:21 pm

Mikej ,, this is the log file ,, latest


15.05.11 22:14:11.001 Debug :
Program Start
15.05.11 22:14:11.002 Debug : Version 1.8.0 Copyright 2015 B9Creations, LLC www.b9creator.com

15.05.11 22:14:11.002 Debug : Relevent Used Application Directories
15.05.11 22:14:11.002 Debug : EXECUTABLE_DIR: "C:/Program Files/B9Creations/B9Creator"
15.05.11 22:14:11.003 Debug : APPLICATION_DIR: "C:/Users/User/AppData/Local/B9Creations, LLC/B9Creator"
15.05.11 22:14:11.004 Debug : TEMP_DIR: "C:/Users/User/AppData/Local/Temp/B9Creator"
15.05.11 22:14:11.005 Debug : DOCUMENTS_DIR: "C:/Users/User/Documents/B9Creator"
15.05.11 22:14:11.808 Debug : B9Layout: Importing Stl Attachments...
15.05.11 22:14:12.079 Debug : UpdateManager: User Started Update Check and Download
15.05.11 22:14:12.223 Debug : B9Update Manager, zero bytes downloaded.
15.05.11 22:14:12.223 Debug : B9Update Manager, Error Message: "Host www.b9creator.com not found"
15.05.11 22:14:12.223 Debug : UpdateManager: Reset Everything
15.05.11 22:14:12.272 Debug : B9SupportStructure: Succesfully Loaded 8 Attachment Types
15.05.11 22:14:13.611 Debug : Hide splash due to firmware update prompt
15.05.11 22:14:15.186 Debug : Using Default Baud rate. port "COM3"
15.05.11 22:14:15.562 Debug : UpdateManager: 60 Local Entrees Loaded
15.05.11 22:14:20.015 Debug : Using Default Baud rate
15.05.11 22:14:20.179 Debug : UpdateManager: 60 Local Entrees Loaded
15.05.11 22:14:33.592 Debug : UpdateManager: 60 Local Entrees Loaded
15.05.11 22:14:35.169 Debug : Using Default Baud rate. port "COM3"
15.05.11 22:14:35.326 Debug : UpdateManager: 60 Local Entrees Loaded
15.05.11 22:14:58.888 Debug : Using Default Baud rate. port "COM3"
15.05.11 22:14:59.037 Debug : UpdateManager: 60 Local Entrees Loaded
ONE SHIP ONE CAPTAIN

User avatar
mazen2014
B9 Maker
B9 Maker
Posts: 157

Re: Vat table problem .. any one had this?

Post#36 » Mon May 11, 2015 1:32 pm

SoftwareVersion 1.8.0 Copyright 2015 B9Creations, LLC www.b9creator.com
Port: COM3
Display Index: 1
Last Print Status: Aborted at layer number 184
Configuration: B9Creator v1.2.0, XY at 30 microns

Job Data
File: C:/Users/User/Desktop/RTP/test 1 BBB.b9j
Name: test 1 BBB
Description: test 1 BBB
XY Pixel Size: 30 µm
Slice Thickness: 30 µm
Total Layers: 271
Material Volume Solid: 0.15 ml, Liquid: 0.15 ml

Material Settings
ID: RedCherry 1:1 Mix, Description: Med-Res, castable
Calc Base: 1.477, Used Base: 1.477
Calc Over: 0.222, Used Over: 0.222
Calc Attach Layers: 2, Used Attach Layers: 2
Calc ABase: 6.648, Used ABase: 6.648
Calc AOver: 0.997, Used AOver: 0.997

Cycle Settings
Unsupported Pixel Multiplier: Unknown
Shutter Open Speed : 80
Shutter Close Speed : 80
Pre Exposure Delay (Settle) : 1
Post Exposure Delay (Kick) : 1
Post Release Delay (Breathe) : 1
Overlift Cutoff (mm) : 3
Initial Overlift (mm) : 1
Subsequent Overlift (mm) : 0.1
Dip (mm) : 0
Dynamic Vat Positioning: true

Job Position
X Offset: 0
Y Offset: 0
Mirrored: false
Show Grid: true

Printer Specific Settings
Configuration Name: B9Creator v1.2.0, XY at 30 microns
Firmware Version: 213
Firmware File: B9C1_2_0.hex
MSM: 1
Slope: 1
Balance: 0
Fade: 0
Lamp Hours: 0
XACM: 1
YACM: 1
Z Backlash: 0
Z Home: 10400
Slide Open: 4100
Slide Home: 590
ONE SHIP ONE CAPTAIN

User avatar
mikej
B9 Moderator
B9 Moderator
Posts: 4189
Contact:

Re: Vat table problem .. any one had this?

Post#37 » Mon May 11, 2015 2:11 pm

mazen2014 wrote:Mikej ,, this is the log file ,, latest



This log file is either incomplete, or from a day that did not have a print attempt.

I need the log file from the day when the error happened during a print attempt.

It will be too big to copy and paste, you'll need to add it as an attachment.
Measure Twice, Cut Once.

User avatar
mazen2014
B9 Maker
B9 Maker
Posts: 157

Re: Vat table problem .. any one had this?

Post#38 » Mon May 11, 2015 2:23 pm

i guessed wrong mike,, i saw the that one , it was impossible to copy past it ,, new lesson i got today .. :)
it is in attachment
Attachments
B9Creator_LOG_150509.txt
(599.53 KiB) Downloaded 95 times
ONE SHIP ONE CAPTAIN

User avatar
mikej
B9 Moderator
B9 Moderator
Posts: 4189
Contact:

Re: Vat table problem .. any one had this?

Post#39 » Mon May 11, 2015 2:31 pm

According to the log file, on layer 183, we sent the command to release and re-position for the next layer. But the printer never responded back that the action was completed.
We then sent the command to turn off the projector, again no response from the printer. Was the projector still on after the error message box was shown, I suspect it was.

It's very difficult to determine exactly what went wrong.

It could be:
- The arduino crashed or lost power.
- The X-motor stuck (but we should have been able to turn off the projector in this case).
- Something with the computer caused a loss of USB communications.
- The USB cord came unplugged.
Measure Twice, Cut Once.

User avatar
mazen2014
B9 Maker
B9 Maker
Posts: 157

Re: Vat table problem .. any one had this?

Post#40 » Mon May 11, 2015 2:34 pm

The projector was on . But it was projecting the main screen ..
Ok i ll check the usb and retry
ONE SHIP ONE CAPTAIN

Return to “Troubleshooting”

Who is online

Users browsing this forum: No registered users and 1 guest

Close Menu Shop Forum