Double print failed

A lost wax capable resin tuned for 70 - 200 micron slice thickness
User avatar
ROSITAGIOIELLI
B9 Maker
B9 Maker
Posts: 334

Double print failed

Post#1 » Tue Aug 05, 2014 9:22 pm

I tried to print to rings with red 50 xy and 75 z with normal parameters the first print is failed because I had few resin in the vat, I filterd and refilled till to the top of the build table but also the second is failed in the more right ring.
What could be happen may be is finish also the second print the resin?
Image
Image

User avatar
Robert Howle
B9 Creator
B9 Creator
Posts: 6629

Double print failed

Post#2 » Tue Aug 05, 2014 9:45 pm

Why such thick slices. Need to show the print data saved.
Dance like nobody's watching!

User avatar
ROSITAGIOIELLI
B9 Maker
B9 Maker
Posts: 334

Double print failed

Post#3 » Tue Aug 05, 2014 11:34 pm

Software Version: Version 1.7.1 Copyright 2014 B9Creations, LLC www.b9creator.com

Last Comm Port: COM3
Display Index: 1
Last Print Attempt Status: Completed
Configuration: B9Creator v1.1.0, XY at 100 microns
Job Name: //Srvsbs/Documenti/Sergio/FILE STL SLC/ANELLO AMETISTA.b9j
Job Data
Name: ANELLO AMETISTA
XY Pixel Size: 50 µm
Slice Thickness: 75 µm
Total Layers: 510
Material Volume: 9.73 ml

Material Settings
ID: B9R-1-Red, Description: General purpose, lost wax suitable.
Calc Base: 4.271, Used Base: 4.271
Calc Over: 0.214, Used Over: 0.214
Calc Attach Layers: 2, Used Attach Layers: 2
Calc ABase: 9.823, Used ABase: 9.823
Calc AOver: 0.492, Used AOver: 0.492

Cycle Settings
Unsupported Pixel Multiplier: 0.8
Shutter Open Speed : 70
Shutter Close Speed : 60
Pre Exposure Delay (Settle) : 2.5
Post Exposure Delay (Kick) : 0.2
Post Release Delay (Breathe) : 1.5
Overlift Cutoff (mm) : 0.5
Initial Overlift (mm) : 3
Subsequent Overlift (mm) : 0
Dip (mm) : 0

Job Position
X Offset: 0
Y Offset: 0
Mirrored: false
Show Grid: true
Hy Robert sorry is 75mic the minimum z slices for red resin? or not? And is for this reasons that I ask for 1:1 red & cherry parameters

User avatar
Robert Howle
B9 Creator
B9 Creator
Posts: 6629

Double print failed

Post#4 » Wed Aug 06, 2014 7:34 am

Why does it say above that the "configuration" is B9 Creator 1.1, xy at 100 microns. Then down further is says "xy pixel 50 microns" Or am I just reading this data output incorrectly.

The setup has to be configured same as the xy resolution u choose. These two have to match. You are set up for 100 xy and trying to print using 50 xy parameters. I didn't even know this was possible to do. It follows for me that u must be very much underexposed.

MIke?

I always like getting feedback from the Mike, when I am problem solving.. I am deff not an "expert" when it comes to other xy settings and setups. I only print at the highest resolution possible, because I only do jewelry.

Robert
Dance like nobody's watching!

User avatar
mikej
B9 Moderator
B9 Moderator
Posts: 4190
Contact:

Double print failed

Post#5 » Mon Aug 11, 2014 3:39 am

Exposures is calculated based on the printer's XY configuration (not the job file layout resolution). So it's OK to layout at a higher resolution than the printer (50XY job, being printed on a 100XY configured printer above), but your actual print will still only be 100 XY in this case.

I suggest you go into Settings and adjust your "Balance" to -.3 (left) or .3(right) towards the side that did not print as well.
Measure Twice, Cut Once.

Return to “B9R-1-Red”

Who is online

Users browsing this forum: No registered users and 1 guest

Close Menu Shop Forum