Search found 2048 matches

Go to advanced search

by akgold
Thu Feb 07, 2019 10:43 pm
Forum: General Discussion
Topic: B9 Create is hollowing out my models
Replies: 1
Views: 188

Re: B9 Create is hollowing out my models

I don't think it is B9 Software The white area is the exposure that is solid red areas (not shown) would be not printed as well as any Black would not be printed. Use the Xray feature in the B9 software to scroll through the design to see if there are any black areas in the middle of the model. Did ...
by akgold
Thu Feb 07, 2019 7:57 pm
Forum: Hardware
Topic: X axis movement malfunction b9 V1.1
Replies: 18
Views: 392

Re: X axis movement malfunction b9 V1.1

one more thing unplug every thing let it sit power, usb, etc.
then plug it all back in again and give it a try.
by akgold
Thu Feb 07, 2019 4:42 pm
Forum: Hardware
Topic: X axis movement malfunction b9 V1.1
Replies: 18
Views: 392

Re: X axis movement malfunction b9 V1.1

NO contact should be happening
by akgold
Thu Feb 07, 2019 1:42 pm
Forum: Software
Topic: How to angle supports?
Replies: 2
Views: 156

Re: How to angle supports?

In the support mode click on one of the supports it will turn white, then click on modify above or where it says add, delete, modify. then you can click on the round base that should be larger at the base than the support itself and hold down the left mouse button and then you can move it around at ...
by akgold
Mon Jan 14, 2019 2:16 pm
Forum: Materials
Topic: Emerald green resin shelf life
Replies: 2
Views: 495

Re: Emerald green resin shelf life

Hi Kristy, I am still using the last of my bottle of green resin that came with my B9 Core printer. It was delivered to me almost 2 years ago in Feb or March of 2017? No I don't print that much and my prints are just fine. I do figurously shake that bottle and let it sit so the bubbles subside for a...
by akgold
Thu Jan 03, 2019 1:40 pm
Forum: Operation
Topic: Files added to flash drive not detected on B9 530
Replies: 5
Views: 358

Re: Files added to flash drive not detected on B9 530

What is " the Ian flash drive "?

Lan or Ian?

I would try a different flash drive as soon as you get that Cpj thing figured out.
by akgold
Wed Jan 02, 2019 10:11 pm
Forum: Operation
Topic: Files added to flash drive not detected on B9 530
Replies: 5
Views: 358

Re: Files added to flash drive not detected on B9 530

It happens to me quite often. I just pull out the usb go back to start over and plug it in. I think it has to do with how much I have loaded on the usb
but it will show up if you go back to transfer.
by akgold
Wed Dec 19, 2018 10:00 pm
Forum: Troubleshooting
Topic: Issue updating B9 -1.2
Replies: 5
Views: 2984

Re: Issue updating B9 -1.2

what version do you have now?
by akgold
Sat Dec 15, 2018 2:38 pm
Forum: General Discussion
Topic: Surface finish is increasing thickness?
Replies: 6
Views: 2119

Re: Surface finish is increasing thickness?

RobertW,
are you using a B9 Core or B91.2Hd?
by akgold
Fri Nov 16, 2018 8:41 pm
Forum: Hardware
Topic: B9 1.2 X axis motor is rattling
Replies: 8
Views: 585

Re: B9 1.2 X axis motor is rattling

or do you mean the motor itself is loose?
if that is the case tighten the screws holding the motor to frame.
by akgold
Fri Nov 16, 2018 8:39 pm
Forum: Hardware
Topic: B9 1.2 X axis motor is rattling
Replies: 8
Views: 585

Re: B9 1.2 X axis motor is rattling

Mark,
You have to check that the hex bolt is tight on the arm that is attached to the motor.
It needs to be set in a position so the screw tightens on the flat part of the motors spindle.
by akgold
Sat Nov 10, 2018 1:55 pm
Forum: General Discussion
Topic: Back of my model
Replies: 6
Views: 768

Re: Back of my model

thanks for attention and answer.i test your model its ok becase the last layer of print is on silicons surface and nutrally is flat and smooth.my problem is one layer of print that one of faces is in resin liquid...that face isnt good and flat surface i think time of resin cure is long...all of my ...
by akgold
Fri Nov 09, 2018 12:21 pm
Forum: General Discussion
Topic: Back of my model
Replies: 6
Views: 768

Re: Back of my model

How are you setting it up to grow?

can you show us a screen shot of your layout?
by akgold
Thu Nov 08, 2018 10:59 pm
Forum: General Discussion
Topic: Odd, sudden change in slicing options
Replies: 2
Views: 282

Re: Odd, sudden change in slicing options

Have you tried to print using the new printing number? It isn't that much difference that you could notice other than a model you have printed in the past might take 5 minutes of more less time to print. only answer is if you upgraded to the newest software and your not satisfied then go to the down...
by akgold
Mon Oct 15, 2018 8:00 pm
Forum: Troubleshooting
Topic: Print detail suddenly poor (emerald, 30x30y, creator1.2)
Replies: 11
Views: 464

Re: Print detail suddenly poor (emerald, 30x30y, creator1.2)

Found it here https://forum.b9c.com/viewtopic.php?f=16&t=7328&p=45963&hilit=FEP#p45963 this is the link posted http://catalog.cshyde.com/item/3d-printing-materials/fep-tape-film-sheet/23-5s-3d-6x6 if you type FEP in the search above on the right on any key word there is a plethora of inf...
by akgold
Mon Oct 15, 2018 6:31 pm
Forum: Troubleshooting
Topic: Print detail suddenly poor (emerald, 30x30y, creator1.2)
Replies: 11
Views: 464

Re: Print detail suddenly poor (emerald, 30x30y, creator1.2)

did you recalibrate the build table????
also people have had great success with adding a layer of the FEP film to the pdms.

viewtopic.php?f=18&t=7452&p=46431&hilit=film%5C#p46431
by akgold
Sun Oct 14, 2018 6:04 pm
Forum: Troubleshooting
Topic: Print detail suddenly poor (emerald, 30x30y, creator1.2)
Replies: 11
Views: 464

Re: Print detail suddenly poor (emerald, 30x30y)

What printer?
if it is a 1.2hd or 1.1 printer then you would need to look at the pdm for fogging.
next check the focus it could have got bumped and calibrate the build table.
by akgold
Wed Oct 10, 2018 5:03 pm
Forum: Official News and Updates
Topic: B9Creator v1.2 production update
Replies: 2
Views: 464

Re: B9Creator v1.2 production update

Thanks Mike
by akgold
Tue Oct 09, 2018 5:53 pm
Forum: Cool Stuff
Topic: offtopic question for jewleryshop owners
Replies: 18
Views: 2232

Re: offtopic question for jewleryshop owners

found this copy on line free to users.
http://www.recyclingsecrets.com/free-re ... m-hoke.pdf

Go to advanced search

Close Menu Shop Forum