Search found 6534 matches

Go to advanced search

by Robert Howle
Sat Feb 23, 2019 9:21 am
Forum: Hardware
Topic: B9CREATOR 1.2 - Z axis/switch not working
Replies: 6
Views: 298

Re: B9CREATOR 1.2 - Z axis/switch not working

Sometimes the back and forth movement of the vat is caused by resin on the photo sensor on the right having resin on it. U can clean using a q tip an ISO.

Robert
by Robert Howle
Fri Feb 22, 2019 5:46 am
Forum: Hardware
Topic: B9CREATOR 1.2 - Z axis/switch not working
Replies: 6
Views: 298

Re: B9CREATOR 1.2 - Z axis/switch not working

check the connections. Had a friend that one had not quite seated.

Robert
by Robert Howle
Wed Feb 20, 2019 1:23 am
Forum: Hardware
Topic: print sticking to duravat
Replies: 3
Views: 326

Re: print sticking to duravat

Def contact support. Never seen this issue before.

Robert
by Robert Howle
Wed Dec 19, 2018 1:37 am
Forum: For Sale
Topic: laser welder for sale
Replies: 2
Views: 1487

laser welder for sale

A store i do work for bought this laser and had me check it out. Worked great. I packed it up and put it in my climate controlled storage. They have decided that they are going to sell it because they have me for their laser work and he is old school and not interested in learning. Packed in origina...
by Robert Howle
Fri Dec 14, 2018 10:40 pm
Forum: Hardware
Topic: print fails
Replies: 3
Views: 1724

Re: print fails

How many lamp hrs?

Did u set the projector settings back because they should not have changed. The only thing is if u set the lamp hrs back to zero then the lamp aging built into the software won't allow for your lamp hrs.

Robert Howle
by Robert Howle
Fri Dec 14, 2018 3:18 pm
Forum: General Discussion
Topic: Surface finish is increasing thickness?
Replies: 6
Views: 2197

Re: Surface finish is increasing thickness?

Not yet but spoke with the factory and they said there should be no increase in print thickness in any direction X,Y, or Z.

Robert
by Robert Howle
Sat Dec 08, 2018 3:17 am
Forum: Hardware
Topic: 110v plug
Replies: 10
Views: 1512

Re: 110v plug

B9 is MIke's company. I think you should listen to his advice.

Robert Howle
by Robert Howle
Fri Dec 07, 2018 7:04 pm
Forum: Hardware
Topic: 110v plug
Replies: 10
Views: 1512

Re: 110v plug

YOu will have to message the people at B9 (factory)

Robert
by Robert Howle
Thu Dec 06, 2018 2:16 am
Forum: Hardware
Topic: 110v plug
Replies: 10
Views: 1512

Re: 110v plug

Under Global Dealer Network might find someone closer to you.

https://www.b9c.com/contact/global-dealer-network

scroll to bottom of page and click on Country to see list of Dealers in that area.

Robert Howle
by Robert Howle
Wed Dec 05, 2018 6:56 pm
Forum: Hardware
Topic: 110v plug
Replies: 10
Views: 1512

Re: 110v plug

You need to message B9 or call the closest distributor in Europe.

Robert Howle
by Robert Howle
Thu Nov 29, 2018 3:48 am
Forum: General Discussion
Topic: printing failed, please help!
Replies: 7
Views: 780

Re: printing failed, please help!

What happens when u run the 'test' print?

Robert
by Robert Howle
Sat Nov 17, 2018 1:10 pm
Forum: Hardware
Topic: B9 1.2 X axis motor is rattling
Replies: 8
Views: 667

Re: B9 1.2 X axis motor is rattling

Great. Usually help here. Thanks everyone.

Robert
by Robert Howle
Fri Nov 16, 2018 11:59 pm
Forum: Hardware
Topic: B9 1.2 X axis motor is rattling
Replies: 8
Views: 667

Re: B9 1.2 X axis motor is rattling

anyone have a motor case they can open and show Mark the position of the gears so he can reassemble.

Robert
by Robert Howle
Fri Nov 16, 2018 7:52 pm
Forum: General Discussion
Topic: Surface finish is increasing thickness?
Replies: 6
Views: 2197

Re: Surface finish is increasing thickness?

Haven't noticed, but will start checking.

Robert
by Robert Howle
Fri Nov 09, 2018 10:45 pm
Forum: General Discussion
Topic: Back of my model
Replies: 6
Views: 885

Re: Back of my model

I would print "snap to floor" make sure back and disc are all planar. If the object is very thick it can suffer from over cure and some items can release from the build table. The red disc are to keep the print on the build table. When printing snap to floor and the item is over 1.5mm in t...
by Robert Howle
Wed Nov 07, 2018 12:03 pm
Forum: Official News and Updates
Topic: Introducing Surface Finish and Queue Software Features for the Core Series & B9Create
Replies: 5
Views: 699

Re: Introducing Surface Finish and Queue Software Features for the Core Series & B9Create

Slicing times are quite a bit longer and saving is longer (larger files). Print times remain the same. Choose what ever slice thickness is available. Recommended or other.

Robert Howle
by Robert Howle
Tue Oct 23, 2018 9:11 pm
Forum: B9R-3-Emerald
Topic: Using B9R Emerald at printer Rapidshape S30L
Replies: 1
Views: 505

Re: Using B9R Emerald at printer Rapidshape S30L

You need to contact others that use your machine and see if any of them are using the resin.

Robert Howle
by Robert Howle
Tue Oct 23, 2018 9:10 pm
Forum: General
Topic: Tethon porcelain resin
Replies: 16
Views: 3401

Re: Tethon porcelain resin

Which Robert?

Robert Howle

Go to advanced search

Close Menu Shop Forum