Search found 302 matches

Go to advanced search

by bvwjewelers
Thu Jun 15, 2017 5:51 pm
Forum: General Discussion
Topic: Question on latest print?
Replies: 27
Views: 5338

Re: Question on latest print?

Well going to try a faster ramp up straight to 1500 now like someone called and suggested to me (thanks!), and after doing everything I can I noticed that my castings have gotten better but far from perfect. I seem to have better luck going back to R&R Plasticast and top burn out of 1500, curing...
by bvwjewelers
Sat May 27, 2017 12:08 pm
Forum: General Discussion
Topic: Question on latest print?
Replies: 27
Views: 5338

Re: Question on latest print?

I love the Core 530...just don't like the resin.
by bvwjewelers
Fri May 26, 2017 5:47 pm
Forum: General Discussion
Topic: Question on latest print?
Replies: 27
Views: 5338

Re: Question on latest print?

I did the new cleaning just like above.....
by bvwjewelers
Fri May 26, 2017 3:12 pm
Forum: General Discussion
Topic: Question on latest print?
Replies: 27
Views: 5338

Re: Question on latest print?

Did the clean up just like was said. Left base on and did UV for 5 min and turned them just in case for another 5 min. Same castings, mixing etc as above.
by bvwjewelers
Tue May 23, 2017 10:57 am
Forum: General Discussion
Topic: Question on latest print?
Replies: 27
Views: 5338

Re: Question on latest print?

I'm still taken back after all this time it's my curing. I'm going to try the DAWN cleaning and new cure times tonight.
by bvwjewelers
Sat May 20, 2017 11:08 am
Forum: General Discussion
Topic: Question on latest print?
Replies: 27
Views: 5338

Re: Question on latest print?

F-me....really! I have been curing for 2 min..so stand them up and cure for 5 min?
by bvwjewelers
Fri May 19, 2017 1:29 pm
Forum: General Discussion
Topic: Question on latest print?
Replies: 27
Views: 5338

Re: Question on latest print?

So I sent off a email to several people about this problem and print fails that seem to be happening from time to time. I am moving over to drilling holes in my kelm and moving away from the air pump I have had installed to see if that does anything tonight on my resin castings. I put down below wha...
by bvwjewelers
Thu May 04, 2017 11:26 am
Forum: General Discussion
Topic: prestege optima investment
Replies: 2
Views: 1131

Re: prestege optima investment

Thank you Sir!
by bvwjewelers
Thu May 04, 2017 11:03 am
Forum: General Discussion
Topic: Question on latest print?
Replies: 27
Views: 5338

Question on latest print?

First off I love the new printer, wow! I ran the test print and it came out flawless right out of the box..second question is these prints I ran this morning. strange line on that large flat surface, should have put that at an angle a bit. The other side of that sprue/base is super smooth, so it's j...
by bvwjewelers
Tue Apr 25, 2017 2:36 pm
Forum: General Discussion
Topic: prestege optima investment
Replies: 2
Views: 1131

prestege optima investment

Anyone else using this for their resin? Trying to find a good mix chart.
by bvwjewelers
Tue Mar 28, 2017 11:46 am
Forum: General Discussion
Topic: Rose Gold Castings?
Replies: 2
Views: 1164

Rose Gold Castings?

So I have noticed ever since going to resin the one thing that is has more problems than any other is casting with rose gold. Does anyone else have this problem or a fix for it? The metal just come out pitted and ruff.
Thanks!
by bvwjewelers
Fri Mar 24, 2017 10:59 am
Forum: General Discussion
Topic: explainations of settings?
Replies: 28
Views: 4232

Re: explainations of settings?

Why is the entire build area exposed creating that large plate of cured resin underneath the rings. No wonder your attach layer is peeling. Just print the oval base and the models and supports snapped to the floor. You are asking for failure and wasteing lots of resin. That layer attached to your b...
by bvwjewelers
Sat Mar 11, 2017 1:18 pm
Forum: General Discussion
Topic: Support and R&D
Replies: 3
Views: 1048

Re: Support and R&D

ok..will try that.
by bvwjewelers
Sat Mar 11, 2017 12:04 pm
Forum: General Discussion
Topic: Support and R&D
Replies: 3
Views: 1048

Support and R&D

Do we know if we are going to have any upgrades to the VATs ? The plastic is still so soft that I only get 2 maybe 3 coats before I have to buy a new VAT due to scratches.
I ultrasound and use my fingers to clean insides and out then scratch free cloth on both sides...still getting hammered. =(
by bvwjewelers
Fri Feb 24, 2017 10:59 am
Forum: General Discussion
Topic: explainations of settings?
Replies: 28
Views: 4232

Re: explainations of settings?

Always snap to layers..This printed last night, it's random. What I did do is leave the build plate attached and just took these off while attached.
by bvwjewelers
Thu Feb 23, 2017 6:02 pm
Forum: General Discussion
Topic: explainations of settings?
Replies: 28
Views: 4232

Re: explainations of settings?

This is weird.
by bvwjewelers
Thu Feb 23, 2017 4:57 pm
Forum: General Discussion
Topic: explainations of settings?
Replies: 28
Views: 4232

Re: explainations of settings?

running another default test now..
by bvwjewelers
Thu Feb 23, 2017 4:25 pm
Forum: General Discussion
Topic: explainations of settings?
Replies: 28
Views: 4232

Re: explainations of settings?

brand new vat, and cleaned the lens when I calibrate. ;/
by bvwjewelers
Thu Feb 23, 2017 3:51 pm
Forum: General Discussion
Topic: explainations of settings?
Replies: 28
Views: 4232

Re: explainations of settings?

Thanks for the help folks. My problem is that it's so random. This look pretty good to me...maybe a larger base plate?
by bvwjewelers
Thu Feb 23, 2017 1:00 pm
Forum: General Discussion
Topic: explainations of settings?
Replies: 28
Views: 4232

Re: explainations of settings?

yes, but they where sticking then noticed they where floating on the new VAT. Was just saying I have all new items and all calibrated
.

Go to advanced search

Close Menu Shop Forum