Hi,

I would like to use my printer with FEP.
I already have 2 aluminum tanks that I bought from Kirk - Adrian_Garland

what advice do you give me?

1) Can we use it with the sweeper
2) What thickness for the adhesive FEP
Thanks for your help

Hello,

do you know what UV Output Factor is in the material catologue

-UV Output Factor
-UV Output Offset
-Projetctor F stop (zoom) multiplier (FSM)



I searched the forum and I found nothing as information

Thank you very much for your valuable advice guys. Robert Howel. Actually, I delete my supports as you said, cut them before UV treatment. and add small drops of resin to plug the small holes. RobertW. I will experiment with spherical end brackets to see the result I wish you all in advance, merry c...

Thanks a lot for your answers.
For points 1 and 2 you can also guide me if you like because when I remove the supports there are marks on the surface. in the media settings, I have 40microns of penetration, then I decrease it to how much to leave the minimum mark on the surface

Hi, 1. Is this kind of support done directly in the B9creator software? otherwise how do you do them Capture.PNG 2. To print a ring, the other small supports that you place, what minimum size of the tip do you recommend to leave a minimum of damage on the printed part? 3.When do you cut the supports...

Aaron RMW, on the last balance setting, I'm at F-0.8 and B +0.4. I have gradually decreased F but I do not see any change. the square of the middle and the 2 square of the top remain in Y between 5.07 and 5.10 mm in Y. do you suggest that I drop F to F-1.0? akgold, thank you for this tip. I will do ...

thank you your help guys

I am a MSM 0.15 S0.25. I am impressed by the speed since the installation of the new lens in the Booster kit 1.1

Thank you Robert.

in fact, what bothers me is the square of the center. in X, i measure 5.02 mm in Y 5.10 mm. there is a gap of 0.08mm.

I may be too perfectionist !

Do you use "dynamic VAT positionning" for your printing ?

I do not understand anything anymore here are more precision and better pictures. Now, i am at MSM 0.15 SLOPE 0.25 Capture.PNG What I was wrong with was that I was trying to print with red resin in 50XY and Z50.8m. And the red resin the minumum advised is 70m. I modified with cherry resin, but not m...

I cheked Daniel.
It's 5mm. My machine is version 1.1

I will watch. I'm sure I put it at 50xy.
my concern is on the top of the print for 5mm squares. that I highlighted in red. in a sense they are bigger.
the rest of the impression is good. I will send pictures of better qualities

I installed the Booster Kit and my printer looks much faster. Now I'm calibrating the printer and I'm stuck. I print with B9C 1.1 xy 50m with red resin The top of my print F + is not square but rectangular. I set F -0.8 but no change. Do you have an idea how to better regulate please 20171116_144528...

Hi,
Where are you from? Switzerland?

Thank you Robert,

This is the glass that I bought in the kit "B9Creator v1.0 & v1.1 Booster Kit" on the site B9C. I have not yet measured it.

Thanks Robert.

The glass on the lamp? By removing the 2 screws?



Need other modifications on the projector?

Hi,

I just bought the booster kit. How to change the projector glass replacement filter please.

Is there any other modifications to be made on the projector D535?

Best

Thank you Robert

Hi,

Do you have good results with the yellow resin for machine V1.1?

I would like to order a resin to do casting, I hesitate between yellow and emerald

Best

Hi,

The reference exists at Digikey.
I will order.

thanks a lot for your help

Thanks Daniel,
There is not a lot of electronics store in Geneva, I wanted to order by internet.

I've been watching since last night. There are several types, I think it is type SP3T but I am not sure
How can I find the reference of the McMaster-Carr article to order the same.