Search found 9 matches

Go to advanced search

by kylerpiercings
Fri Feb 21, 2020 5:42 pm
Forum: For sale
Topic: B9 530 for sale.
Replies: 2
Views: 286

Re: B9 530 for sale.

Sure! I’m moving on to an envisiontec. Absolutely nothing is wrong with the unit and has been recently serviced by B9. It’s wonderful unit that works reliably and without fail. If budgeting allowed I’d keep it as a second or backup unit.
by kylerpiercings
Fri Feb 21, 2020 8:24 am
Forum: For sale
Topic: B9 530 for sale.
Replies: 2
Views: 286

B9 530 for sale.

Selling our b9 530 with cleaning station, two build plates, two vats, one of which has less than three prints on. $8000
by kylerpiercings
Wed May 01, 2019 8:43 pm
Forum: Troubleshooting
Topic: Failure code 10019
Replies: 1
Views: 404

Failure code 10019

I checked before posting, but after upgrading my firmware for the slate grey a couple weeks ago, I started getting a failure code 10019 on the b9 530. I factory reset the unit and the error code went away, however today I started seeing it again and I cannot get anything to print. I've submitted a t...
by kylerpiercings
Tue Feb 19, 2019 9:49 pm
Forum: Hardware
Topic: print sticking to duravat
Replies: 3
Views: 478

Re: print sticking to duravat

Hey! Thanks for your reply, yes, I did recharge the vats between cycles. I used both emerald and yellow
by kylerpiercings
Tue Feb 19, 2019 2:51 pm
Forum: Hardware
Topic: print sticking to duravat
Replies: 3
Views: 478

print sticking to duravat

So I'm getting prints stuck to both of my duravats in the same exact location on both units. Both of them are undamaged as far as I can see, and the build plate doesn't seem to have any damage. Any advice?
by kylerpiercings
Thu Feb 07, 2019 8:06 pm
Forum: General Discussion
Topic: B9 Create is hollowing out my models
Replies: 1
Views: 354

B9 Create is hollowing out my models

Hey again folks.

I'm running into this issue where B9 Create wants to hollow out my solid models some 1700 layers in. I don't know why it's wanting to do this. The file created in matrix is definitely solid.
by kylerpiercings
Wed Feb 06, 2019 9:31 pm
Forum: Software
Topic: How to angle supports?
Replies: 2
Views: 332

How to angle supports?

Hello all, we're pretty new to the B9 (I'm also currently a solos user). My question is how to angle supports? Currently I can only get them to populate straight, so if I'm printing a ring the supports have to make contact with the inside of the shank.
by kylerpiercings
Wed Jan 02, 2019 4:07 pm
Forum: Operation
Topic: Files added to flash drive not detected on B9 530
Replies: 5
Views: 656

Re: Files added to flash drive not detected on B9 530

Thank you so must for the quick reply. It’s prongtest.cpj_30xy_30z.cpj.b9j
by kylerpiercings
Wed Jan 02, 2019 1:14 pm
Forum: Operation
Topic: Files added to flash drive not detected on B9 530
Replies: 5
Views: 656

Files added to flash drive not detected on B9 530

Hey guys and gals. I just received a used b9 530 in the mail today and got everything moving and set up. For some reason files stored to the Ian flash drive do not seem to be detected on the unit.

I’ve done a layout and slice, it’s the only thing on the drive. What gives?

Go to advanced search

cron
Close Menu Shop Forum